View FT2232D_4187627.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TM
Future Technology Devices International Ltd.
FT2232D Dual USB UART/FIFO I.C.
The FT2232D is an updated version of FTDI's 3rd generation USB UART / FIFO I.C. family.This device features two Multi-Purpose UART / FIFO controllers which can be configured individually in several different modes. As well as a UART interface, FIFO interface and Bit-Bang IO modes of the 2nd generation FT232BM and FT245BM devices, the FT2232D offers a variety of additional new modes of operation, including a Multi-Protocol Synchronous Serial Engine interface which is designed specifically for synchronous serial protocols such as JTAG, I2C, and SPI bus. The FT2232D is fully pin to pin compatible with the previous FT2232C and FT2232L devices. In addition to supporting all of the FT2232C / FT2232L functionallity, the FT2232D has an additional interface mode, CPU FIFO mode, and is specified for -40 to +85 degrees C operation. The FT2232D is available in Pb-free (RoHS compliant) compact 48-Lead LQFP package.
Copyright (c) Future Technology Devices International Ltd. 2006
FT2232D Dual USB UART / FIFO I.C.
1.1 Features Summary 1.1 Hardware Features
* * * * * * * * * * * * * * * *
Single chip USB to dual channel serial / parallel ports with a variety of configurations. Entire USB protocol handled on the chip...no USBspecific firmware programming required. FT232B-style asynchronous serial UART interface option with full hardware handshaking and modem interface signals. UART Interface supports 7 / 8 bit data, 1 / 2 stop bits, and Odd / Even / Mark / Space / No Parity Fully assisted hardware or X-On / X-Off software handshaking. Transfer Data Rate 300 to 1 Mega Baud (RS232). Transfer Data Rate 300 to 3 Mega Baud (at TTL levels and RS422 / RS485). Auto transmit enable control for RS485 serial applications using TXDEN pin. In-built support for event characters and line break condition. Transmit and receive LED drive signals on each channel. FT245B-style FIFO interface option with bidirectional data bus and simple 4 wire handshake interface. USB to parallel FIFO transfer data rate up to 1 megabyte / second. Adjustable receive buffer timeout. Enhanced bit-bang Mode interface option with RD# and WR# strobes. New synchronous bit-bang mode interface option with RD# and WR# strobes. New Multi-Protocol Synchronous Serial Engine (MPSSE) interface option.
* * * * * * * * * * * * * * * * * * * * *
New CPU-style FIFO interface mode option. New MCU host bus emulation mode option. New fast opto-Isolated serial interface mode option High I/O pin output drive option. Interface mode and USB Description strings configurable in external EEPROM. EEPROM Configurable on board via USB Support for USB suspend and resume conditions via PWREN#, and SI/WU pins. Support for bus powered, self powered, and highpower bus powered USB configurations. Integrated power-on-reset circuit, with optional reset input and reset Output pins. 5V and 3.3V logic I/O Interfacing with independent level conversion on each channel. Integrated 3.3V LDO regulator for USB I/O Integrated 6MHz - 48Mhz clock multiplier PLL USB Bulk data transfer mode. 4.35V to 5.25V single supply operating voltage range. Low operating and USB suspend current. UHCI / OHCI / EHCI host controller compatible. USB 2.0 Full Speed (12 Mbits / Second) compatible. Extended -40C to 85C industrial operating temperature range. Compact 48-LD Lead Free LQFP package FTDI's royalty-free VCP and D2XX drivers eliminate the requirement for USB driver development in most cases. Dedicated Windows DLLs available for USB to JTAG, USB to SPI, and USB to I2C applications.
1.2 Driver Support
Royalty-Free VIRTUAL COM PORT (VCP) DRIVERS for... * Windows 98, 98SE, ME, 2000, Server 2003, XP. * Windows Vista / Longhorn* * Windows XP 64-bit.* * Windows XP Embedded. * Windows CE.NET 4.2 & 5.0 * MAC OS 8 / 9, OS-X * Linux 2.4 and greater Royalty-Free D2XX Direct Drivers (USB Drivers + DLL S/W Interface) * Windows 98, 98SE, ME, 2000, Server 2003, XP. * Windows Vista / Longhorn* * Windows XP 64-bit.* * Windows XP Embedded. * Windows CE.NET 4.2 & 5.0 * MAC OS-X * Linux 2.4 and greater
The drivers listed above are all available to download for free from the FTDI website. Various 3rd Party Drivers are also available for various other operating systems - see the FTDI website for details.
* Currently Under Development. Contact FTDI for availability.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 2 of 51
FT2232D Dual USB UART / FIFO I.C.
* * * * * * * * * * * USB to Dual Port RS232 Converters USB to Dual Port RS422 / RS485 Converters Upgrading Legacy Peripheral Designs to USB USB Instrumentation USB JTAG Programming USB to SPI Bus Interfaces USB Industrial Control Field Upgradable USB Products Galvanically Isolated Products with USB Interface USB to synchronous serial interface Cellular and cordless phone USB data transfer cables and interfaces.
1.3 Typical Applications
* * * * * * * * * * *
Interfacing MCU / PLD / FPGA based designs to USB USB Audio and Low Bandwidth Video data transfer PDA to USB data transfer USB Smart Card Readers USB Instrumentation USB Industrial Control USB MP3 Player Interface USB FLASH Card Reader / Writers Set Top Box PC - USB interface USB Digital Camera Interface USB Bar Code Readers
1.2
General Description
The FT2232D is a USB interface which incorporates the functionallity of two of FTDI's second generation BM chips into a single device. A single downstream USB port is converted to two IO channels which can each be individually configured as a FT232BM-style UART interface, or a FT245BM-style FIFO interface, without the need to add a USB hub. There are also several new special modes which are either enabled in the external EEPROM, or by using driver commands. These include Synchronous Bit-Bang Mode, a CPU-Style FIFO Interface Mode, a Multi-Protocol Synchronous Serial Engine Interface Mode, MCU Host Bus Emulation Mode, and Fast Opto-Isolated Serial Interface Mode. In addition a new high drive level option means that the device UART / FIFO IO pins will drive out at around three times the normal power level, meaning that the bus can be shared by several devices. Classic BM-style Asynchronous Bit-Bang Mode is also supported, but has been enhanced to give the user access to the device's internal RD# and WR# strobes. FTDI provide a royalty free Virtual Com Port (V.C.P) driver that makes the peripheral ports look like a standard COM port to the PC. Most existing software applications should be able interface with the Virtual Com Port simply by reconfiguring them to use the new ports created by the driver. Using the VCP drivers an application programmer would communicate with the device in exactly the same way as they would a regular PC COM port - using the Windows VCOMM API calls or a COM port library. The FT2232D driver also incorporates the functions defined for FTDI's D2XX drivers, allowing applications programmers to interface software directly to the device using a Windows DLL. Details of the driver and the programming interface can be found on FTDI's website at www.ftdichip.com.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 3 of 51
FT2232D Dual USB UART / FIFO I.C.
2.0
Features and Enhancements
The FT2232D incorporates all of the enhancements introduced for the second generation FT232BM and FT245BM chips. These are summarised as follows :* Two Individually Configurable IO Channels Each of the FT2232D's Channels (A and B) can be individually configured as a FT232BM-style UART interface, or as a FT245BM-style FIFO interface. In addition these channel can be configured in a number of special IO modes. * Integrated Power-On-Reset (POR) circuit The device incorporates an internal POR function. A RESET# pin is available to allow external logic to reset the device where required, however for most applications this pin can simply be hardwired to Vcc. A RSTOUT# pin is provided in order to allow the new POR circuit to provide a stable reset to external MCU and other devices. * Integrated RCCLK circuit Used to ensure that the oscillator and clock multiplier PLL frequency are stable prior to USB enumeration. * Integrated level converter on UART / FIFO interface and control signals Each channel of the FT2232D has its own independent VCCIO pin that can be supplied by between 3V to 5V. This allows each channel's output voltage drive level to be individually configured. Thus allowing, for example 3.3V logic to be interfaced to the device without the need for external level converter I.C.'s. * Improved power management control for highpower USB Bus Powered devices The PWREN# pin will become active when the device is enumerated by USB, and be deactivated when the device is in USB suspend. This can be used to directly drive a transistor or P-Channel MOSFET in applications where power switching of external circuitry is required. The BM pull down enable feature (configured in the external EEPROM) DS2232D Version 0.91 * * * is also retained. This will make the device gently pull down on the FIFO / UART IO lines when the power is shut off (PWREN# is high). In this mode any residual voltage on external circuitry is bled to GND when power is removed, thus ensuring that external circuitry controlled by PWREN# resets reliably when power is restored. Support for Isochronous USB Transfers Whilst USB Bulk transfer is usually the best choice for data transfer, the scheduling time of the data is not guaranteed. For applications where scheduling latency takes priority over data integrity such as transferring audio and low bandwidth video data, the FT2232D offers the option of USB Isochronous transfer via configuration of bit in the EEPROM. Send Immediate / Wake Up Signal Pin on each channel There is a Send Immediate / Wake Up (SI/WU) signal pins on each of the chips channels. These combine two functions on one pin. If USB is in suspend mode (and remote wakeup is enabled in the EEPROM), strobing this pin low will cause the device to request a resume from suspend (WakeUp) on the USB Bus. Normally, this can be used to wake up the Host PC. During normal operation, if this pin is strobed low any data in the device RX buffer will be sent out over USB on the next Bulk-IN request from the drivers regardless of the packet size. This can be used to optimise USB transfer speed for some applications. Low suspend current The suspend current of the FT2232D is typically under 100 A (excluding the 1.5K pull up resistor on USBDP) in USB suspend mode. This allows greater margin for peripherals to meet the USB Suspend current limit of 500uA.
(c) Future Technology Devices International Ltd. 2006 Page of 51
FT2232D Dual USB UART / FIFO I.C.
* Programmable Receive Buffer Timeout The TX buffer timeout is programmable over USB in 1ms increments from 1ms to 255ms, thus allowing the device to be better optimised for protocols requiring faster response times from short data packets. * Relaxed VCC Decoupling The improved level of Vcc decoupling that was incorporated into BM devices has also been implemented in the FT2232D device. * Baud Rate Pre-Scaler Divisors The FT2232D (UART mode) baud rate pre-scaler supports division by (n+0), (n+0.125), (n+0.25), (n+0.375), (n+0.5), (n+0.625), (n+0.75) and (n+0.875) where n is an integer between 2 and 16,384 (214). * * Extended EEPROM Support The FT2232D supports 93C46 (64 x 16 bit), 93C56 (128 x 16 bit), and 93C66 (256 x 16 bit) EEPROMs. The extra space is not used by the device, however it is available for use by other external MCU / logic whilst the FT2232D is being held in reset. There is now an adiitional 64 words of space available (128 bytes total) in the user area when a 93C56 or 93C66 is used. USB 2.0 (full speed option) An EEPROM based option allows the FT2232D to return a USB 2.0 device descriptor as opposed to USB 1.1. Note : The device would be a USB 2.0 Full Speed device (12Mb/s) as opposed to a USB 2.0 High Speed device (480Mb/s).
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 5 of 51
FT2232D Dual USB UART / FIFO I.C.
In addition to the BM chip features, the FT2232D incorporates the following new features and interface modes :* Enhanced Asynchronous Bit-Bang Interface The FT2232D supports FTDI's BM chip Bit Bang mode. In Bit Bang mode, the eight FIFO data lines can be switched between FIFO interface mode and an 8-bit Parallel IO port. Data packets can be sent to the device and they will be sequentially sent to the interface at a rate controlled by an internal timer (equivalent to the baud rate prescaler). With the FT2232D device this mode has been enhanced so that the internal RD# and WR# strobes are now brought out of the device which can be used to allow external logic to be clocked by accesses to the BitBang IO bus. * Synchronous Bit-Bang Interface Synchronous Bit-Bang Mode differs from Asynchronous Bit-Bang mode in that the device is only read when it is written to. Thus making it easier for the controlling program to measure the response to an output stimulus as the data returned is synchronous to the output data. High Output Drive Level Capabillity The IO interface pins can be made to drive out at three times the standard drive level thus allowing multiple devices, or devices that require a greater drive strength to be interfaced to the FT2232D. This option is configured in the external EEPROM, ad can be set individually for each channel. normally be un-configured (i.e. have no defined function) at power-up. Application software on the PC could use the MPSSE to download configuration data to the FPGA over USB. This data would define the hardware's function on power up. The other FT2232 channel would be available for other devices. This approach would allow a customer to create a "generic" USB peripheral, who's hardware function can be defined under control of the application software. The FPGA based hardware could be easily upgraded or totally changed simply by changing the FPGA configuration data file. (See FTDI's MORPHIC development module for a practicle example, www.morph-ic.com) * MCU Host Bus Emulation This new mode combines the `A' and `B' bus interface to make the FT2232D interface emulate a standard 8048 / 8051 style MCU bus. This allows peripheral devices for these MCU families to be directly attached to the FT2232D with IO being performed over USB with the help of MPSSE interface technology. CPU-Style FIFO Interface The CPU style FIFO interface is essentially the same function as the classic FT245 interface, however the bus signals have been redefined to make them easier to interface to a CPU bus. Fast Opto-Isolated Serial Interface A new proprietary FTDI protocol is designed to allow galvanically isolated devices to communicate sychronously with the FT2232D using just 4 signal wires (over two dual opto-isolators), and two power lines. The peripheral circuitry controls the data transfer rate in both directions, whilst maintaining full data integrity. Maximum USB full speed data rates can be acheived. Both `A' and `B' channels can communicate over the same 4 wire interface if desired.
*
*
* Multi-Protocol Synchronous Serial Engine Interface (M.P.S.S.E.) The Multi-Protocol Synchronous Serial Engine (MPSSE) interface is a new option designed to interface efficiently with synchronous serial protocols such as JTAG and SPI Bus. It is very flexible in that it can be configured for different industry standards, or proprietary bus protocols. For instance, it is possible to connect one of the FT2232D's channels to an SRAM configurable FPGA as supplied by vendors such as Altera and Xilinx. The FPGA device would DS2232D Version 0.91
*
(c) Future Technology Devices International Ltd. 2006 Page 6 of 51
FT2232D Dual USB UART / FIFO I.C.
3.0
Simplified Block Diagram
PWREN# 48MHz Baud Rate Generator ADBUS0 ADBUS1 ADBUS2 Dual Port TX Buffer 128 bytes ADBUS3 ADBUS4 MultiPurpose UART / FIFO Controller ADBUS5 ADBUS6 ADBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3
Channel A
VCC
PWRCTL
3V3OUT
3.3 Volt LDO Regulator
Dual Port RX Buffer 384 Bytes
USBDP USB Transceiver USBDM
Serial Interface Engine ( SIE )
USB Protocol Engine
SI/WUA
Channel B
Dual Port TX Buffer 128 bytes
BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 BCBUS0 BCBUS1 BCBUS2
USB DPLL
Dual Port RX Buffer 384 Bytes
MultiPurpose UART / FIFO Controller
XTOUT 6MHZ Oscillator XTIN TEST GND x8 Clock Multiplier
48MHz 48MHz 12MHz
Baud Rate Generator 3V3OUT
BCBUS3 SI/WUB
EECS EEPROM Interface EESK EEDATA RESET# RESET GENERATOR RSTOUT#
Figure 1 - FT2232D Simplified Block Diagram 3.1
*
Functional Block Descriptions
3.3V LDO Regulator The 3.3V LDO Regulator generates the 3.3 volt reference voltage for driving the USB transceiver cell output buffers. It requires an external decoupling capacitor to be attached to the 3V3OUT regulator output pin. It also provides 3.3V power to the RSTOUT# pin. The main function of this block is to power the USB Transceiver and the Reset Generator Cells rather than to power external logic. However, external circuitry requiring 3.3V nominal at a current of not greater than 5mA could also draw its power from the 3V3OUT pin if required. * USB Transceiver The USB Transceiver Cell provides the USB 1.1 / USB 2.0 full-speed physical interface to the USB cable. The output drivers provide 3.3 volt level slew rate control signalling, whilst a differential receiver and two single ended receivers provide USB data in, SEO and USB Reset condition detection. USB DPLL The USB DPLL cell locks on to the incoming NRZI USB data and provides separate recovered clock and data signals to the SIE block.
*
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page of 51
FT2232D Dual USB UART / FIFO I.C.
* 6MHz Oscillator The 6MHz Oscillator cell generates a 6MHz reference clock input to the x8 Clock multiplier from an external 6MHz crystal or ceramic resonator. x Clock Multiplier The x8 Clock Multiplier takes the 6MHz input from the Oscillator cell and generates a 48MHz reference clock for the USB DPPL and the Baud Rate Generator blocks. Serial Interface Engine (SIE) The Serial Interface Engine (SIE) block performs the Parallel to Serial and Serial to Parallel conversion of the USB data. In accordance to the USB 2.0 specification, it performs bit stuffing / unstuffing and CRC5 / CRC16 generation / checking on the USB data stream. * USB Protocol Engine The USB Protocol Engine manages the data stream from the device USB control endpoint. It handles the low level USB protocol (Chapter 9) requests generated by the USB host controller and the commands for controlling the functional parameters of the UART / FIFO controller blocks. Dual Port TX Buffers (128 bytes) Data from the USB data out endpoint is stored in the Dual Port TX buffer and removed from the buffer to the transmit register under control of the UART FIFO controller. Dual Port RX Buffers (384 bytes) Data from the UART / FIFO controller receive register is stored in the Dual Port RX buffer prior to being removed by the SIE on a USB request for data from the device data in endpoint. Multi-Purpose UART / FIFO Controllers The Multi-purpose UART / FIFO controllers handle the transfer of data between the Dual Port RX and TX buffers and the UART / FIFO transmit and receive registers. When configured as a UART it performs asynchronous 7 / 8 bit Parallel to Serial and Serial to Parallel conversion of the data on the RS232 (RS422 and RS485) interface. Control signals supported by UART mode include RTS, CTS, DSR , DTR, DCD and RI. There are also transmitter enable control signal pins (TXDEN) provided to assist with interfacing to RS485 transceivers. RTS/CTS, DSR/DTR and Xon/Xoff handshaking options are also supported. Handshaking, where required, is handled in hardware to ensure fast response times. The UART's also supports the RS232 BREAK setting and detection conditions. * Baud Rate Generator The Baud Rate Generator provides a x16 clock input to the UART's from the 48MHz reference clock and consists of a 14 bit prescaler and 3 register bits which provide fine tuning of the baud rate (used to divide by a number plus a fraction). This determines the Baud Rate of the UART which is programmable from 183 baud to 3 million baud. * RESET Generator The Reset Generator Cell provides a reliable power-on reset to the device internal circuitry on power up. An additional RESET# input and RSTOUT# output are provided to allow other devices to reset the FT2232D, or the FT2232D to reset other devices respectively. During reset, RSTOUT# is driven low, otherwise it drives out at the 3.3V provided by the onboard regulator. RSTOUT# can be used to control the 1.5K pull-up on USBDP directly where delayed USB enumeration is required. It can also be used to reset other devices. RSTOUT# will stay highimpedance for approximately 5ms after VCC has risen above 3.5V AND the device oscillator is running AND RESET# is high. RESET# should be tied to VCC unless it is a requirement to reset the device from external logic or an external reset generator I.C.
*
*
*
*
*
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page of 51
FT2232D Dual USB UART / FIFO I.C.
* EEPROM Interface When used without an external EEPROM the FT2232D be configured as a USB to dual serial port device. Adding an external 93C46 (93C56 or 93C66) EEPROM allows each of the chip's channels to be independently configured as a serial UART (232 mode), or a parallel FIFO (245 mode). The external EEPROM is used to enable the Fast Opto-Isolated Serial interface mode. The external EEPROM can also be used to customise the USB VID, PID, Serial Number, Product Description Strings and Power Descriptor value of the FT2232D for OEM applications. Other parameters controlled by the EEPROM include Remote Wake Up, Isochronous Transfer Mode, Soft Pull Down on Power-Off and USB 2.0 descriptor modes. The EEPROM should be a 16 bit wide configuration such as a MicroChip 93LC46B or equivalent capable of a 1Mb/s clock rate at VCC = 4.35V to 5.25V. The EEPROM is programmableon board over USB using a utility program available from FTDI's web site (www.ftdichip. com). This allows a blank part to be soldered onto the PCB and programmed as part of the manufacturing and test process. If no EEPROM is connected (or the EEPROM is blank), the FT2232D will default to dual serial ports. The device use its built-in default VID, PID Product Description and Power Descriptor Value. In this case, the device will not have a serial number as part of the USB descriptor.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 9 of 51
FT2232D Dual USB UART / FIFO I.C.
.0
Device Pin-Out
6
PWREN# BDBUS0
BDBUS1 BDBUS2
3V3OUT
A V C C
46
V C C
3
V C C
42
BDBUS3
AGND
XTOUT
EECS TEST
AVCC
V C C I O A
31 14
V C C I O B ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 24 23 22 21 20 19 17 16 15 13 12 11 10 40 39 38 37 36 35 33 32 30 29 28 27 26 41
XTIN
VCC
8
USBDM
7
USBDP
EESK EEDATA VCC RESET# RSTOUT# 3V3OUT USBDP USBDM GND SI/WUA ACBUS3 ACBUS2
1
48
37 36
ACBUS0 ACBUS1 ACBUS2 ACBUS3 SI/WUA BDBUS0
BDBUS4 BDBUS5 GND BDBUS6 BDBUS7 VCCIOB BCBUS0 BCBUS1 BCBUS2 BCBUS3 SI/WUB GND
5 4
RSTOUT# RESET#
FT2232D FT2232L
XXYY
12 13 25 24
FTDI
43
XTIN
BDBUS1 BDBUS2 BDBUS3 BDBUS4
44 48 1 2 47
XTOUT EECS EESK EEDATA TEST A G N D
BDBUS5 BDBUS6 BDBUS7 BCBUS0 BCBUS1 BCBUS2 BCBUS3 G GG G SI/WUB N NN N D D D D PWREN#
ACBUS1
VCCIOA ACBUS0
ADBUS7
ADBUS6
GND ADBUS5
ADBUS4
ADBUS3 ADBUS2
ADBUS1
ADBUS0
45
34 25 18 9
Figure 2 Pin-Out (Lead Free LQFP- Package )
Figure 3 Pin-Out (Schematic Symbol )
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 10 of 51
FT2232D Dual USB UART / FIFO I.C.
5.0
Pin Definitions
This section decribes the operation of the FT2232D pins. Common pins are defined in the first section, then the I/O pins are defined, by chip mode. More detailed descriptions of the operation of the I/O pins are provided in section 9.
5.1
Common Pins
The operation of the following FT2232D pins stay the same, regardless of the chip mode :USB INTERFACE GROUP Pin# 7 8 Signal USBDP USBDM Type I/O I/O Description USB Data Signal Plus ( Requires 1.5K pull-up to 3V3OUT or RSTOUT# ) USB Data Signal Minus
EEPROM INTERFACE GROUP Pin# 48 1 2 Signal EECS EESK EEDATA Type I/O I/O Description EEPROM - Chip Select. Tri-State during device reset. **Note 1 EEPROM - Data I/O Connect directly to Data-In of the EEPROM and to DataOut of the EEPROM via a 2.2K resistor. Also, pull Data-Out of the EEPROM to VCC via a 10K resistor for correct operation. Tri-State during device reset. **Note 1
OUTPUT Clock signal to EEPROM. Tri-State during device reset, else drives out. **Note 1
MISCELLANEOUS SIGNAL GROUP Pin# 4 5 Signal RESET# RSTOUT# Type INPUT Description Can be used by an external device to reset the FT2232D. If not required, tie to VCC. **Note 1
OUTPUT Output of the internal Reset Generator. Drives low for 5.6 ms after VCC > 3.5V and the internal clock starts up, then clamps it's output to the 3.3V output of the internal regulator. Taking RESET# low will also force RSTOUT# to drive low. RSTOUT# is NOT affected by a USB Bus Reset. INPUT Puts device into I.C. test mode - must be tied to GND for normal operation. OUTPUT Goes Low after the device is configured via USB, then high during USB suspend. Can be used to control power to external logic using a P-Channel Logic Level MOSFET switch. Enable the Interface Pull-Down Option in EEPROM when using the PWREN# pin in this way. INPUT Input to 6MHz Crystal Oscillator Cell. This pin can also be driven by an external 6MHz clock if required. Note : Switching threshold of this pin is VCC/2, so if driving from an external source, the source must be driving at 5V CMOS level or a.c. coupled to centre around VCC/2.
47 41
TEST PWREN#
43
XTIN
44
XTOUT
OUTPUT Output from 6MHz Crystal Oscillator Cell. XTOUT stops oscillating during USB suspend, so take care if using this signal to clock external logic.
**Note 1 - During device reset, these pins are tri-state but pulled up to VCC via internal 200K resistors.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 11 of 51
POWER AND GND GROUP Pin# 6 Signal 3V3OUT Type Description
FT2232D Dual USB UART / FIFO I.C.
OUTPUT 3.3 volt Output from the integrated L.D.O. regulator This pin should be decoupled to GND using a 33nF ceramic capacitor in close proximity to the device pin. It's prime purpose is to provide the internal 3.3V supply to the USB transceiver cell and the RSTOUT# pin. A small amount of current (<= 5mA) can be drawn from this pin to power external 3.3V logic if required. PWR PWR +4.35 volt to +5.25 volt VCC to the device core, LDO and non-UART / FIFO controller interface pins. +3.0 volt to +5.25 volt VCC to the UART / FIFO A Channel interface pins 10..13, 15..17 and 19..24. When interfacing with 3.3V external logic in a bus powered design connect VCCIO to a 3.3V supply generated from the USB bus. When interfacing with 3.3V external logic in a self powered design connect VCCIO to the 3.3V supply of the external logic. Otherwise connect to VCC to drive out at 5V CMOS level. +3.0 volt to +5.25 volt VCC to the UART / FIFO B Channel interface pins 26..30, 32..33 and 35..40. When interfacing with 3.3V external logic in a bus powered design connect VCCIO to a 3.3V supply generated from the USB bus. When interfacing with 3.3V external logic in a self powered design connect VCCIO to the 3.3V supply of the external logic. Otherwise connect to VCC to drive out at 5V CMOS level. Device - Ground Supply Pins Device - Analog Power Supply for the internal x8 clock multiplier. A low pass filter consisting of a 470 Ohm series resistor and a 100 nF to GND should be used on the supply to this pin. Device - Analog Ground Supply for the internal x8 clock multiplier
3, 42 14
VCC VCCIOA
31
VCCIOB
PWR
9,18, 25, 34 GND 46 AVCC
PWR PWR
45
AGND
PWR
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 12 of 51
FT2232D Dual USB UART / FIFO I.C.
5.2
IO Pin Definitions by Chip Mode
The FT2232D will default to dual serial mode (232 UART mode on both channel A and B, if no external EEPROM is used, or the external EEPROM is blank. The definition of the following pins vary according to the chip's mode :-
Channel A
Pin Definitions by Chip Mode **Note 2 Pin# Generic Pin Name 232 UART 245 FIFO Mode Mode Enhanced Asynchronous MPSSE and **Note Synchronous Bit-Bang Modes D0 D1 D2 D3 D4 D5 D6 D7 WR# **Note 6 RD# **Note 6 WR# **Note RD# **Note SI/WUA TCK/SK TDI/D0 TDO/DI TMS/CS GPIOL0 GPIOL1 GPIOL2 GPIOL3 GPIOH0 GPIOH1 GPIOH2 GPIOH3 **Note MCU Host Bus Emulation Mode **Note 5 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 I/O0 I/O1 IORDY OSC **Note Fast OptoIsolated Serial Mode **Note 3 CPU FIFO Interface Mode
24 23 22 21 20 19 17 16 15 13 12 11 10
ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 SI/WUA
TXD RXD RTS# CTS# DTR# DSR# DCD# RI# TXDEN SLEEP# RXLED# TXLED# SI/WUA
D0 D1 D2 D3 D4 D5 D6 D7 RXF# TXE# RD# WR SI/WUA
D0 D1 D2 D3 D4 D5 D6 D7 CS# A0 RD# WR# **Note
**Note 2 : 232 UART, 245 FIFO, CPU FIFO Interface, and Fast Opto-Isolated modes are enabled in the external EEPROM. Enhanced Asynchronous and Synchronous Bit-Bang modes, MPSSE, and MCU Host Bus Emulation modes are enabled using the driver command set bit mode. See Section 5.2 for details. **Note 3 : Channel A can be configured in another IO mode if channel B is in Fast Opto-Isolated Serial Mode. If both Channel A and Channel B are in Fast Opto-Isolated Serial Mode all of the IO will be on Channel B. **Note : MPSSE is Channel A only. **Note 5 : MCU Host Bus Emulation requires both Channels. **Note 6 : The Bit-Bang Mode (synchronous and asynchronous) WR# and RD# strobes are on these pins when the main Channel mode is 245 FIFO, CPU FIFO interface, or Fast Opto-Isolated Serial Modes. **Note : The Bit-Bang Mode (synchronous and asynchronous) WR# and RD# strobes are on these pins when the main Channel mode is 232 UART Mode. **Note : SI/WU is not available in these modes.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 13 of 51
FT2232D Dual USB UART / FIFO I.C.
Channel B
Pin Definitions by Chip Mode **Note 2 Pin# Generic Pin Name 232 UART 245 FIFO Mode Mode Enhanced Asynchronous MPSSE and **Note Synchronous Bit-Bang Modes D0 D1 D2 D3 D4 D5 D6 D7 WR# **Note 9 RD# **Note 9 WR# **Note RD# **Note SI/WUB **Note MCU Host Bus Emulation Mode **Note 5 A8 A9 A10 A11 A12 A13 A14 A15 CS# ALE RD# WR# **Note SI/WUB Fast OptoIsolated Serial Mode FSDI FSCLK FSDO FSCTS **Note 3 CPU FIFO Interface Mode
40 39 38 37 36 35 33 32 30 29 28 27 26
BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 BCBUS0 BCBUS1 BCBUS2 BCBUS3 SI/WUB
TXD RXD RTS# CTS# DTR# DSR# DCD# RI# TXDEN SLEEP# RXLED# TXLED# SI/WUB
D0 D1 D2 D3 D4 D5 D6 D7 RXF# TXE# RD# WR SI/WUB
D0 D1 D2 D3 D4 D5 D6 D7 CS# A0 RD# WR# **Note
**Note 2 : 232 UART, 245 FIFO, CPU FIFO Interface, and Fast Opto-Isolated modes are enabled in the external EEPROM. Enhanced Asynchronous and Synchronous Bit-Bang modes, MPSSE, and MCU Host Bus Emulation modes are enabled using the driver command set bit mode. See Section 5.2 for details. **Note 3 : Channel A can be configured in another IO mode if channel B is in Fast Opto-Isolated Serial Mode. If both Channel A and Channel B are in Fast Opto-Isolated Serial Mode all of the IO will be on Channel B. **Note : MPSSE is Channel A only. **Note 5 : MCU Host Bus Emulation requires both Channels. **Note 6 : The Bit-Bang Mode (synchronous and asynchronous) WR# and RD# strobes are on these pins when the main Channel mode is 245 FIFO, CPU FIFO interface, or Fast Opto-Isolated Serial Modes. **Note : The Bit-Bang Mode (synchronous and asynchronous) WR# and RD# strobes are on these pins when the main Channel mode is 232 UART Mode. **Note : SI/WU is not available in these modes. **Note 9 : The Bit-Bang Mode (synchronous and asynchronous) WR# and RD# strobes are on these pins when the main Channel mode is 245 FIFO, CPU FIFO interface. Bit-Bang mode is not available on Channel B when Fast OptoIsolated Serial Mode is enabled.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 1 of 51
FT2232D Dual USB UART / FIFO I.C.
5.3
IO Mode Command Hex Values
Enhanced Asynchronous and Synchronous Bit-Bang modes, MPSSE, and MCU Host Bus Emulation modes are enabled using the D2XX driver command FT_SetBitMode. The hex values used with this command to enable these modes are as followsMode Reset the IO bit Mode Asynchronous Bit Bang Mode MPSSE Synchronous Bit bang Mode MCU Host bus Emulation Fast Opto-Isolated Serial Mode Value (hex) 0 1 2 4 8 10
See application note AN2232L-02 "Bit Mode Functions for the FT2232D" for more details and examples. Note that all other device modes can be enabled in the external EEPROM, and do not require these values to be configured. In the case of Fast Opto-Isolated Serial mode sending a value of 10 will hold this device mode in reset, and sending a value of 0 will release this mode from reset.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 15 of 51
FT2232D Dual USB UART / FIFO I.C.
6.0
Package Outline
Figure - LD Lead Free LQFP Package Dimensions
9 PIN# 48 7
Pin# 1
FTDI
FT2232D FT2232L XXYY
79
0.22+/- 0.05
0.5
1.0 1o +/- 1o 2
1.4 +/- 0.05
0.24 +/- 0.07
1.60 MAX
0.09 Min 0.2 Max 0.25 0.2 Min 0.6 +/- 0.15 0.22 +/- 0.05
0.09 Min 0.16 Max
0.05 Min 0.15 Max
The FT2232D is supplied in a 48 pin lead (Pb) free LQFP package. This package has a 7mm x 7mm body (9mm x 9mm including leads) with leads on a 0.5mm pitch. The FT2232D is fully compliant with the European Union RoHS directive. The above drawing shows the LQFP-48 package - all dimensions are in millimetres. . XXYY = Date Code ( XX = 2 digit week number, YY = 1 or 2 digit year number.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 16 of 51
FT2232D Dual USB UART / FIFO I.C.
7.0
Absolute Maximum Ratings
These are the absolute maximum ratings for the FT2232D device in accordance with the Absolute Maximum Rating System (IEC 60134). Exceeding these may cause permanent damage to the device. * * * * * * * * * * * Storage Temperature .......................................................................................... -65oC to + 150oC Floor Life (Out of Bag) at Factory Ambient (30oC/60% Relative Humidity)........................192 Hours **Note 10 (Level 3 Compliant) Ambient Temperature (Power Applied)......................................................................... -40oC to + 85oC VCC Supply Voltage .............................................................................................. -0.5V to +6.00V DC Input Voltage - Inputs ....................................................................................... -0.5V to VCC + 0.5V DC Input Voltage - High Impedance Bidirectionals ...................................................... -0.5V to VCC + 0.5V DC Output Current - Outputs .................................................................................. 24mA DC Output Current - Low Impedance Bidirectionals ..................................................... 24mA Power Dissipation (VCC = 5.25V) ............................................................................. 500mW Electrostatic Discharge Voltage (Human Body Model) (I < 1A) ..................................... +/- 3000V Latch Up Current (Vi = +/- 10V maximum, for 10 ms) ................................................... +/-200mA
**Note 10 - If devices are stored out of the packaging beyond this time limit the devices should be baked before use. The devices should be ramped up to a temperature of 110oC and baked for 8 to 10 hours.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 1 of 51
FT2232D Dual USB UART / FIFO I.C.
.1
D.C. Characteristics
DC Characteristics ( Ambient Temperature = 0 to 70oC ) Operating Voltage and Current Parameter Vcc1 Vcc2 Icc1 Icc2 Description VCC Operating Supply Voltage VCCIO Operating Supply Voltage Operating Supply Current Operating Supply Current Min 4.35 3.0 Typ 5.0 30 100 Max 5.25 5.25 200 Units V V mA A Normal Operation USB Suspend **Note 11 Conditions
**Note 11 - Supply current excludes the 200A nominal drawn by the external pull-up resistor on USBDP. IO Pin Characteristics ( VCCIO = 5.0V, Standard Drive Level ) **Note 12 Parameter Voh Vol Vin VHys Description Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis Min 3.2 0.3 1.3 50 Typ 4.1 0.4 1.6 55 Max 4.9 0.6 1.9 60 Units V V V mV Conditions I source = 2mA I sink = 2mA
IO Pin Characteristics ( VCCIO = 3.0 - 3.6V, Standard Drive Level ) **Note 12 Parameter Voh Vol Vin VHys Description Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis Min 2.2 0.3 1.0 20 Typ 2.7 0.4 1.2 25 Max 3.2 0.5 1.5 30 Units V V V mV Conditions I source = 1 mA I sink = 2 mA
IO Pin Characteristics ( VCCIO = 5.0V, High Drive Level ) **Note 12, **Note 13 Parameter Voh Vol Vin VHys Description Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis Min 3.2 0.3 1.3 50 Typ 4.1 0.4 1.6 55 Max 4.9 0.6 1.9 60 Units V V V mV Conditions I source = 6 mA I sink = 6 mA
IO Pin Characteristics ( VCCIO = 3.0 - 3.6V, High Drive Level ) **Note 12, **Note 13 Parameter Voh Vol Vin VHys Description Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis Min 2.2 0.3 1.0 20 Typ 2.8 0.4 1.2 25 Max 3.2 0.6 1.5 30 Units V V V mV Conditions I source = 3mA I sink = 8 mA
**Note 12 : Inputs have an internal 200K pull-up resistor to VCCIO, which can alternativly be programmed to pull down using a configuration bit in the external EEPROM. **Note 12 : The high output drive level is configured in the external EEPROM. Each channel can be configured individually. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 1 of 51
FT2232D Dual USB UART / FIFO I.C.
XTIN / XTOUT Pin Characteristics Parameter Voh Vol Vin Description Output Voltage High Output Voltage Low Input Switching Threshold Min 4.0 0.1 1.8 Typ 2.5 Max 5.0 1.0 3.2 Units V V V Conditions Fosc = 6MHz Fosc = 6MHz
RESET#, TEST, EECS, EESK, EEDATA Pin Characteristics **Note 1 Parameter Voh Vol Vin VHys Description Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis Min 3.2 0.3 1.3 50 Typ 4.1 0.4 1.6 55 Max 4.9 0.6 1.9 60 Units V V V mV Conditions I source = 2mA I sink = 2 mA
**Note 1 - EECS, EESK, EEDATA and RESET# pins have an internal 200K pull-up resistor to VCC RSTOUT# Pin Characteristics Parameter Voh Vol Description Output Voltage High Output Voltage Low Min 3.0 0.3 Typ Max 3.6 0.6 Units V V Conditions I source = 2mA I sink = 2mA
USB IO Pin Characteristics **Note 15 Parameter UVoh UVol UVse UCom UVDif UDrvZ Description IO Pins Static Output ( High) IO Pins Static Output ( Low ) Single Ended Rx Threshold Differential Common Mode Differential Input Sensitivity Driver Output Impedance Min 2.8 0 0.8 0.8 0.2 29 Typ Max 3.6 0.3 2.0 2.5 Units V V V V V Ohm Conditions RI = 1.5K to 3V3Out ( D+ ) RI = 15K to GND ( D- ) RI = 1.5K to 3V3Out ( D+ ) RI = 15K to GND ( D- )
-
44
**Note 15 - Driver Output Impedance includes the external 27R series resistors on USBDP and USBDM pins.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 19 of 51
8.0 8.1
Standard Device Configuration Examples Oscillator Configurations
FT2232D Dual USB UART / FIFO I.C.
FT2232C
FT2232D
27pF 43
FT2232C
FT2232D
XTIN
43 3-Pin Resonator 6MHz
XTIN
1M
2 - Pin Resonator or Crystal 6MHz 27pF 44
44
XTOUT
XTOUT
Figure 5 3-Pin Ceramic Resonator Configuration
Figure 6 Crystal or 2-Pin Ceramic Resonator Configuration
Figure 5 illustrates how to use the FT2232D with a 3-Pin Ceramic Resonator. A suitable part would be a ceramic resonator from Murata's CERALOCK range. (Murata Part Number CSTCR6M00G15), or equivalent. 3-Pin ceramic resonators have the load capacitors built into the resonator so no external loading capacitors are required. This makes for an economical configuration. The accuracy of this Murata ceramic resonator is +/- 0.25% and it is specifically designed for USB full speed applications. A 1 MegaOhm loading resistor across XTIN and XTOUT is recommended in order to guarantee this level of accuracy. Other ceramic resonators with a lesser degree of accuracy (typically +/- 0.5%) are technically out-with the USB specification, but it has been calculated that using such a device will work satisfactorily in practice with a FT2232D design. An example of such a device is Murata's CSTLSM00G53. Figure 6 illustrates how to use the FT2232D with a 6MHz Crystal or 2-Pin Ceramic Resonator. In this case, these devices do not have in-built loading capacitors so these have to be added between XTIN, XTOUT and GND as shown. A value of 27pF is shown as the capacitor in the example - this will be good for many crystals and some resonators but do select the value based on the manufacturers recommendations wherever possible. If using a crystal, use a parallel cut type. If using a resonator, see the previous note on frequency accuracy. It is also possible to use a 6 MHz Oscillator with the FT2232D. In this case the output of the oscillator would be connected to XTIN, and XTOUT should be left unconnected. The oscillator must have a CMOS output.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 20 of 51
8.2
EEPROM Configuration
FT2232C 48 EECS 1 EESK 2 EEDATA
FT2232D Dual USB UART / FIFO I.C.
Figure 7 illustrates how to connect the FT2232D to the 93C46 (93C56 or 93C66) EEPROM. EECS (pin 48) is directly connected to the chip select (CS) pin of the EEPROM. EESK (pin 1) is directly connected to the clock (SK) pin of the EEPROM. EEDATA (pin 2) is directly connected to the Data In (Din) pin of the EEPROM. There is a potential condition whereby both the Data Output (Dout) of the EEPROM can drive out at the same time as the EEDATA pin of the FT2232D. To prevent potential data clash in this situation, the Dout of the EEPROM is connected to EEDATA of the FT2232D via a 2.2K resistor.
VCC
FT2232D
EEPROM - 93C46 / 56 / 66 1 2 2.2K 3 4 CS SK DIN DOUT VCC NC NC GND 8 7 6 5
Following a power-on reset or a USB reset, the FT2232D will scan the EEPROM to find out (a) if an EEPROM is attached to the Device and (b) if the data in the device is valid. If both of these are the case, then the FT2232D will use the data in the EEPROM, otherwise it will use its built-in default values and configuration. The default port configuration of the FT2232D puts both Channel A and Channel B into serial UART mode.
When a valid command is issued to the EEPROM from the FT2232D, the EEPROM will acknowledge the command by VCC 10K pulling its Dout pin low. In order to check for this condition, it is necessary to pull Dout high using a 10K resistor. If the Figure command acknowledge doesn't happen then EEDATA will be EEPROM Configuration pulled high by the 10K resistor during this part of the cycle and the device will detect an invalid command or no EEPROM present. There are two varieties of 93C46/56/66 EEPROM's on the market - one is configured as being 16 bits wide, the other is configured as being 8 bits wide. These are available from many sources such as Microchip, STMicro, ISSI etc. The FT2232D requires EEPROM's with a 16-bit wide configuration such as the Microchip 93LC46B device. The EEPROM must be capable of reading data at a 1Mb clock rate at a supply voltage of 4.35V to 5.25V. Most available parts are capable of this. Check the manufacturers data sheet to find out how to connect pins 6 and 7 of the EEPROM. Some devices specify these as no-connect, others use them for selecting 8 / 16 bit mode or for test functions. Some other parts have their pinout rotated by 90o so please select the required part and its options carefully. It is possible to "share" the EEPROM between the FT2232D and another external device such as an MCU. However, this can only be done when the FT2232D is in its reset condition as it tri-states its EEPROM interface at that time. A typical configuration would use four bits of an MCU IO Port. One bit would be used to hold the FT2232D reset (using RESET#) on power-up, the other three would connect to the EECS, EESK and EEDATA pins of the FT2232D in order to read / write data to the EEPROM at this time. Once the MCU has read / written the EEPROM, it would take RESET# high to allow the FT2232D to configure itself and enumerate over USB. The external EEPROM can be programmed over USB using utility software provided by FTDI. The external EEPROM is used to enable 245 FIFO, and Fast Opto-Isolated Serial interface modes on each channel. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 21 of 51
FT2232D Dual USB UART / FIFO I.C.
8.3
USB Bus Powered and Self Powered Configuration
Figure 8 - USB Bus Powered Configuration
USB "B" Connector Ferrite Bead VCC 1 2 3 4 5 10nF 27R 27R 6 33nF 3 V C C 42 V C C 14 31 V C C I O A V C C I O A 470R 0.1uF A V C C
46
3v3OUT
8 7
USB DM USB DP
1.5K 5
FT2232D FT2232C
RSTOUT#
43 XTIN 6MHz 44 XTOUT VCC 27pF 27pF 10K VCC 4 48 RESET#
EECS 1 EESK 2 EEDATA TEST A G N D 45 G N D G N D 9 G N D 18 25 G N D 34
+ 0.1uF 0.1uF 10uF
47
Decoupling Capacitors
Figure 8 illustrates the FT2232D in a typical USB bus powered configuration. A USB Bus Powered device gets its power from the USB bus. Basic rules for USB Bus power devices are as follows - a) On plug-in, the device must draw no more than 100mA b) On USB Suspend the device must draw no more than 500A. c) A High Power USB Bus Powered Device (one that draws more than 100mA) should use the PWREN# pin to keep the current below 100mA on plug-in and 500A on USB suspend. d) A device that consumes more than 100mA can not be plugged into a USB Bus Powered Hub e) No device can draw more that 500mA from the USB Bus. The power descriptor in the EEPROM should be programmed to match the current draw required by the device. A Ferrite Bead is connected in series with USB power to prevent noise from the device and associated circuitry (EMI) being radiated down the USB cable to the Host. The value of the Ferrite Bead depends on the total current required by the circuit - a suitable range of Ferrite Beads is available from Steward (www.steward.com) for example Steward Part # MI0805K400R-00 also available from DigiKey, Part # 240-1035-1. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 22 of 51
Figure 9 - USB Self Powered Configuration
USB "B" Connector VCC 1 2 3 4 27R 27R 6 33nF 4.7K 8 7 10K USB DM USB DP 3 V C C 42 V C C
FT2232D Dual USB UART / FIFO I.C.
470R
14 31 V C C I O A V C C I O B
46 A V C C
0.1uF
3v3OUT
FT2232D FT2232C
1.5K 5 VCC 4 47 +
RSTOUT# RESET#
0.1uF
0.1uF
10uF
A TEST G N D 45
G N D
G N D
G N D
G N D
9 18 25 34
Decoupling Capacitors
Figure 9 illustrates the FT2232D in a typical USB self powered configuration. A USB Self Powered device gets its power from its own POWER SUPPLY and does not draw current from the USB bus. The basic rules for USB Self power devices are as follows - a) A Self-Powered device should not force current down the USB bus when the USB Host or Hub Controller is powered down. b) A Self Powered Device can take as much current as it likes during normal operation and USB suspend as it has its own POWER SUPPLY. c) A Self Powered Device can be used with any USB Host and both Bus and Self Powered USB Hubs. The USB power descriptor option in the EEPROM should be programmed to a value of zero (self powered). To meet requirement a) the 1.5K pull-up resistor on USBDP is connected to RSTOUT# as per the bus-power circuit. However, the USB Bus Power is used to control the RESET# Pin of the FT2232D device. When the USB Host or Hub is powered up RSTOUT# will pull the 1.5K resistor on USBDP to 3.3V, thus identifying the device as a full speed device to USB. When the USB Host or Hub power is off, RESET# will go low and the device will be held in reset. As RESET# is low, RSTOUT# will also be low, so no current will be forced down USBDP via the 1.5K pull-up resistor when the host or hub is powered down. Failure to do this may cause some USB host or hub controllers to power up erratically. Note : When the FT2232D is in reset, the I/O interface pins all go tri-state. These pins have internal 200K pull-up resistors to VCCIO, so they will gently pull high unless driven by some external logic. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 23 of 51
FT2232D Dual USB UART / FIFO I.C.
. Interfacing to 3.3V Logic Figure 10 - Bus Powered Circuit with 3.3V logic drive and IO supply voltage
3.3V LDO Regulator
In Gnd 0.1uF Out VCC3V3
3.3V Power to External Logic
Ferrite Bead 1 27R 27R
VCC 3 V C C 6 8 7 42 V C C 14 31 V C C I O A V C C I O B
470R
USB "B" Connector
2 3 4 10nF
46 A V C C
0.1uF
33nF
3v3OUT USB DM USB DP
VCC3V3
SI/WUA
10
VCC 1.5K + 0.1uF 0.1uF 10uF VCC 5
FT2232D FT2232C
VCC3V3 RSTOUT# SI/WUB A G N D 45 G N D G N D 9 G N D 18 25 G N D 34 26
Decoupling Capacitors
4 RESET# 47 TEST
Figure 10 shows how to configure the FT2232D to interface with a 3.3V logic devices. In this example, a discrete 3.3V regulator is used to supply the 3.3V logic from the USB supply. VCCIOA and VCCIOB are connected to the output of the 3.3V regulator, which in turn will cause the device interface IO pins on both channels to drive out at 3.3V level. It is also possible to have one IO interface channel driving out at 5V level, and the other at 3.3V level. In this case one of the VCCIO pins would be connected to 5V, and the other connected to 3.3V. For USB bus powered circuits some considerations have to be taken into account when selecting the regulator - a) The regulator must be capable of sustaining its output voltage with an input voltage of 4.35 volts. A Low Drop Out (LDO) regulator must be selected. b) The quiescent current of the regulator must be low in order to meet the USB suspend total current requirement of <= 500A during USB suspend. An example of a regulator family that meets these requirements is the MicroChip (Telcom) TC55 Series. These devices can supply up to 250mA current and have a quiescent current of under 1A. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 2 of 51
FT2232D Dual USB UART / FIFO I.C.
In some cases, where only a small amount of current is required (< 5mA) , it may be possible to use the in-built regulator of the FT2232D to supply the 3.3V without any other components being required. In this case, connect VCCIOA or VCCIOB to the 3V3OUT pin of the FT2232D. Note : It should be emphasised that the 3.3V supply for VCCIO in a bus powered design with a 3.3V logic interface should come from an LDO which is supplied by the USB bus, or from the 3V3OUT pin of the FT232BM, and not from any other source. Please also note that if the SI/WU pins are not being used they should be pulled up to the same supply as their respective VCCIO pin.
Figure 11 - Self Powered Circuit with 3.3V logic drive and IO supply voltage
VCC3V3 USB "B" Connector 470R 1 2 3 4 VCC5V
27R 27R
0.1uF
46 A V C C 3v3OUT
3 V C C
42
14 31 VVV CCC CCC II OO AB SI/WUA 10
6 33nF 4.7K 8 7 10K
VCC3V3
USB DM USB DP
FT2232D FT2232C
VCC3V3
1.5K 5 VCC5V 4 +
RSTOUT# RESET# TEST SI/WUB 26 A G N D G N D G N D G N D G N D 34
0.1uF
0.1uF
10uF
Decoupling Capacitors
45
9 18 25
Figure 11 is an example of a FT2232D USB self powered design with 3.3V interface. In this case the VCCIOA and VCCIOB pins are supplied by an external 3.3V supply in order to make both of the device's IO channels drive out at 3.3V logic level, thus allowing them to be connected to a 3.3V MCU or other external logic. It is also possible to have one IO interface channel driving out at 5V level, and the other at 3.3V level. In this case one of the VCCIO pins would be connected to 5V, and the other connected to 3.3V. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 25 of 51
FT2232D Dual USB UART / FIFO I.C.
A USB self powered design uses its own power supplies, and does not draw any of its power from the USB bus. In such cases, no special care need be taken to meet the USB suspend current (0.5 mA) as the device does not get its power from the USB port. As with bus powered 3.3V interface designs, in some cases, where only a small amount of current is required (<5mA), it may be possible to use the in-built regulator of the FT2232D to supply the 3.3V without any other components being required. In this case, connect VCCIOA or VCCIOB to the 3V3OUT pin of the FT2232D. Note that if the SI/WU pins are not being used they should be pulled up to the same supply as their respective VCCIO pin.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 26 of 51
FT2232D Dual USB UART / FIFO I.C.
.5 Power Switching Figure 12 - Bus Powered Circuit with Power Control
P-Channel Power MOSFET
s d
Switched 5V Power to External Logic 0.1uF
g
0.1uF Soft Start 1K Circuit 470R
USB "B" Connector
Ferrite Bead 1 2 3 4 10nF 27R 27R
VCC
33nF
3 42 14 31 V V VV C C CC C C CC II 6 3V3OUT OO AB
46 A V C C
0.1uF
FT2232C FT2232D
VCC 8 7 + 0.1uF 0.1uF 10uF VCC 4 RESET# USB DM USB DP PWREN# 41
1.5K 5 RSTOUT#
Decoupling Capacitors
USB Bus powered circuits need to be able to power down in USB suspend mode in order to meet the <= 500A total suspend current requirement (including external logic). Some external logic can power itself down into a low current state by monitoring the PWREN# pin. For external logic that cannot power itself down in that way, the FT2232D provides a simple but effective way of turning off power to external circuitry during USB suspend. Figure 12 shows how to use a discrete P-Channel Logic Level MOSFET to control the power to external logic circuits. A suitable device would be an International Rectifier (www.irf.com) IRLML6402, or equivalent. It is recommended that a "soft start" circuit consisting of a 1K series resistor and a 0.1 F capacitor are used to limit the current surge when the MOSFET turns on. Without the soft start circuit there is a danger that the transient power surge of the MOSFET turning on will reset the FT2232D, or the USB host / hub controller. The values used here allow attached circuitry to power up with a slew rate of ~12.5 V per millisecond, in other words the output voltage will transition from GND to 5V in approximately 400 microseconds.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 2 of 51
FT2232D Dual USB UART / FIFO I.C.
Alternatively, a dedicated power switch I.C. with inbuilt "soft-start" can be used instead of a MOSFET. A suitable power switch I.C. for such an application would be a Micrel (www.micrel.com) MIC2025-2BM or equivalent. Please note the following points in connection with power controlled designs - a) The logic to be controlled must have its own reset circuitry so that it will automatically reset itself when power is reapplied on coming out of suspend. b) Set the Pull-down on Suspend option in the FT2232D's EEPROM. c) For USB high-power bus powered device (one that consumes greater than 100 mA, and up to 500 mA of current from the USB bus), the power consumption of the device should be set in the max power field in the EEPROM. A high-power bus powered device must use this descriptor in the EEPROM to inform the system of its power requirements. d) For 3.3V power controlled circuits the VCCIO pins must not be powered down with the external circuitry. Either connect the power switch between the output of the 3.3V regulator and the external 3.3V logic, or if appropriate power the VCCIO pin from the 3V3OUT pin of the FT2232D.
Figure 13 - Bus Powered Circuit with Power Control and 3.3V Logic Drive / IO Supply Voltage
3.3V LDO Regulator IN OUT GND VCC3V3 0.1uF
g
P-Channel Power MOSFET
s d
Switched 3.3V Power to External Logic 0.1uF 0.1uF Soft Start 1K Circuit
USB "B" Connector
Ferrite Bead 1 2 3 4 10nF 27R 27R
VCC5V
470R
33nF
3 42 14 31 V V VV C C CC C C CC II 6 3V3OUT OO AB
46 A V C C
0.1uF
VCC3V3
FT2232D FT2232
VCC5V 8 USB DM 7 USB DP + 0.1uF 0.1uF 10uF VCC5V 4 RESET# 1.5K 5 RSTOUT#
SI/WUA
10 VCC3V3
SI/WUB
26
Decoupling Capacitors
PWREN#
41
Figure 13 is a FT2232D design example which effectively combines the circuits shown in Figures 13 and 14 to give a USB bus powered design with power switching and 3.3V logic drive level on both channels. Once again a P-Channel Power MOSFET and soft start circuit are used to control the power to external logic devices. A 3.3V LDO regulator which is supplied by the USB bus is used to provide the 3.3V supply for the VCCIO pins, as well as the external logic. If the SI/WU pins are not being used they should be pulled up to 3.3V. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 2 of 51
FT2232D Dual USB UART / FIFO I.C.
9.0 Signal Descriptions By IO Mode and Interface Channel Configurations 9.1 232 UART Interface Mode Signal Descriptions and Interface Configurations
When either Channel A or Channel B are in 232 UART mode the IO signal lines are configured as follows:Pin# Channel A 24 23 22 21 20 19 17 16 Channel B 40 39 38 37 36 35 33 32 TXD RXD RTS# CTS# DTR# DSR# DCD# RI# OUTPUT Transmit Asynchronous Data Output INPUT INPUT INPUT INPUT INPUT Receive Asynchronous Data Input **Note 16 Clear To Send Control Input / Handshake signal **Note 16 Data Set Ready Control Input / Handshake signal **Note 16 Data Carrier Detect Control Input **Note 16 Ring Indicator Control Input. When the Remote Wake up option is enabled in the EEPROM, taking RI# low can be used to resume the PC USB Host controller from suspend. **Note 16 OUTPUT Request To Send Control Output / Handshake signal OUTPUT Data Terminal Ready Control Output / Handshake signal Signal Type Description
15 13
30 29
TXDEN
OUTPUT Enable Transmit Data for RS485
SLEEP# OUTPUT Goes low during USB Suspend Mode. Typically used to powerdown an external TTL to RS232 level converter I.C. in USB to RS232 converter designs. RXLED# O.C. TXLED# O.C SI/WU INPUT LED Drive - Pulses Low when Transmitting Data via USB. LED Drive - Pulses Low when Receiving Data via USB. The Send Immediate / WakeUp signal combines two functions on a single pin. If USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in the EEPROM , strobing this pin low will cause the device to request a resume on the USB Bus. Normally, this can be used to wake up the Host PC. During normal operation (PWREN# = 0), if this pin is strobed low any data in the device TX buffer will be sent out over USB on the next Bulk-IN request from the drivers regardless of the pending packet size. This can be used to optimise USB transfer speed for some applications. Tie this pin to VCCIO if not used.
12 11 10
28 27 26
**Note 16 : These pins are pulled to up VCCIO via internal 200K resistors during Reset and USB Suspend mode. These can be programmed to gently pull low during USB suspend ( PWREN# = "1" ) by setting this option in the EEPROM.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 29 of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 14 - USB <=> Dual Port RS232 Converter Configuration
FT2232D
Figure 14 illustrates how to connect the FT2232D, when both channels A and B are configured as 232-style UART interfaces, to two TTL - RS232 Level Converter I.C.'s to make a USB <=> Dual Port RS232 converter using the popular "213" series of TTL to RS232 level converters. These devices have 4 transmitters and 5 receivers in a 28LD SSOP package and feature an in-built voltage converter to convert the 5V (nominal) VCC to the +/- 9 volts required by RS232. An important feature of these devices is the SHDN# pin which can power down the device to a low quiescent current during USB suspend mode. The device used in the example above is a Sipex SP213EHCA which is capable of RS232 communication at up to 500K baud. If a lower baud rate is acceptable, then several pin compatible alternatives are available such as the Sipex SP213ECA , the Maxim MAX213CAI and the Analog Devices ADM213E, which are all good for communication at up to 115,200 baud. If a higher baud rate is desired, use a Maxim MAX3245CAI part which is capable of RS232 communication at rates of up to 1M baud. The MAX3245 is not pin compatible with the 213 series devices, also its SHDN pin is active high, so connect it to PWREN# instead of SLEEP#. Dual RS232 level converters such as the Maxim MAX3187 may also be a suitable alternative.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 30 of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 15 - USB <=> RS422 Converter Configuration
FT2232C FT2232D
PWREN# SLEEP# (ACBUS1) TXD (ADBUS0) RXD (ADBUS1) RTS# (ADBUS2) CTS# (ADBUS3) DTR# (ADBUS4) DSR# (ADBUS5) DCD# (ADBUS6) RI# (ADBUS7) TXDEN (ACBUS0) 41 13 24 23 22 21 20 19 17 16 15 6 4 5 3 2 11 R 7 VCC 14 SP491 4 SLEEP# (BCBUS1) TXD (BDBUS0) RXD (BDBUS1) RTS# (BDBUS2) CTS# (BDBUS3) DTR# (BDBUS4) DSR# (BDBUS5) DCD# (BDBUS6) RI# (BDBUS7) TXDEN (BCBUS0) 29 5 40 3 39 38 6 37 36 35 5 33 32 30 3 2 11 R 6 7 12 120R CTSM_B D VCC 14 SP491 4 10 9 RTSM_B RTSP_B CTSP_B GND 7 RXDM_B 2 11 R 12 120R D 10 9 12 120R CTSM_A 10 D 9 RTSM_A RTSP_A CTSP_A 4 5 3 2 11 R 6 7 VCC 14 SP491 12 120R RXDM_A 10 D 9 VCC 14 SP491
DB9-M RS422 Channel A
TXDM_A TXDP_A RXDP_A
GND
DB9-M RS422 Channel B
TXDM_B TXDP_B RXDP_B
Figure 15 illustrates how to connect the UART interfaces of the FT2232D to two TTL - RS422 Level Converter I.C.'s to make a USB to dual port RS422 converter. There are many such level converter devices available - this example uses two Sipex SP491 devices which have enables on both their transmitters and receivers. Because the transmitter enables are active high, they are connected to the SLEEP# pins. The receiver enables are active low and are both connected to the PWREN# pin. This ensures that both the transmitters and receivers are enabled when the device is active, and disabled when the device is in USB suspend mode. If the design is USB BUS powered, it may be necessary to use a P-Channel logic level MOSFET (controlled by PWREN#) in the VCC line of the SP491 devices to ensure that the USB standby current of 500A is met. The SP491 is good for sending and receiving data at a rate of up to 5M Baud - in this case the maximum rate is limited to 3M Baud by the FT2232D. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 31 of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 16 - USB <=> RS485 Converter Configuration
FT2232C FT2232D
PWREN# SLEEP# (ACBUS1) TXD (ADBUS0) RXD (ADBUS1) RTS# (ADBUS2) CTS# (ADBUS3) DTR# (ADBUS4) DSR# (ADBUS5) DCD# (ADBUS6) RI# (ADBUS7) TXDEN (ACBUS0) 41 13 24 23 22 21 20 19 17 16 15 LINK 3 4 2 1 R 5 120R D 6 8 VCC SP481 7
DB9-M RS485 Channel A
DM_A DPA GND
SLEEP# (BCBUS1) TXD (BDBUS0) RXD (BDBUS1) RTS# (BDBUS2) CTS# (BDBUS3) DTR# (BDBUS4) DSR# (BDBUS5) DCD# (BDBUS6) RI# (BDBUS7) TXDEN (BCBUS0)
29 40 39 38 37 36 35 33 32 30
3 4 2 1 R 5 D
8
VCC SP481 7
DB9-M RS485 Channel B
DM_B DP_B GND
6
120R LINK
Figure 16 illustrates how to connect the UART interfaces of the FT2232D to two TTL - RS485 Level Converter I.C.'s to make a USB to dual port RS485 converter. This example uses two Sipex SP491 devices but there are similar parts available from Maxim and Analog Devices amongst others. The SP491 is a RS485 device in a compact 8 pin SOP package. It has separate enables on both the transmitter and receiver. With RS485, the transmitter is only enabled when a character is being transmitted from the UART. The TXDEN pins on the FT2232D are provided for exactly that purpose, and so the transmitter enables are wired to the TXDEN's. The receiver enable is active low, so it is wired to the PWREN# pin to disable the receiver when in USB suspend mode. RS485 is a multi-drop network - i.e. many devices can communicate with each other over a single two wire cable connection. The RS485 cable requires to be terminated at each end of the cable. Links are provided to allow the cable to be terminated if the device is physically positioned at either end of the cable. In this example the data transmitted by the FT2232D is also received by the device that is transmitting. This is a common feature of RS485 and requires the application software to remove the transmitted data from the received data stream. With the FT2232D it is possible to do this entirely in hardware - simply modify the schematic so that RXD of the FT2232D is the logical OR of the SP481 receiver output with TXDEN using an HC32 or similar logic gate. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 32 of 51
FT2232D Dual USB UART / FIFO I.C.
9.2 232 UART Mode LED Interface
VCCIO
VCCIO
TX
RX
LED
FT2232D
FT2232C
TXLED# RXLED#
220R
220R
220R
FT2232C
FT2232D
TXLED# RXLED#
Figure 1 Dual LED Configuration
Figure 1 Single LED Configuration
When configured in UART mode the FT2232D has two IO pins on each channel dedicated to controlling LED status indicators, one for transmitted data the other for received data. When data is being transmitted / received the respective pins drive from tri-state to low in order to provide indication on the LED's of data transfer. A digital one-shot timer is used so that even a small percentage of data transfer is visible to the end user. Figure 17 shows a configuration using two individual LED's - one for transmitted data the other for received data. In Figure 18, the transmit and receive LED indicators are wire-OR'ed together to give a single LED indicator which indicates any transmit or receive data activity. Another possibility (not shown here) is to use a 3 pin common anode tri-color LED based on the circuit in Figure 18 to have a single LED that can display activity in a variety of colors depending on the ratio of transmit activity compared to receive activity. Note that the LED's are connected to the same supply as VCCIO.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 33 of 51
FT2232D Dual USB UART / FIFO I.C.
9.3
245 FIFO Interface Mode Signal Descriptions and Configuration
When either Channel A or Channel B are in 245 FIFO mode the IO signal lines are configured as follows. FIFO DATA BUS GROUP **Note 1 Pin# Channel A 24 23 22 21 20 19 17 16 Channel B 40 39 38 37 36 35 33 32 D0 D1 D2 D3 D4 D5 D6 D7 I/O I/O I/O I/O I/O I/O I/O I/O FIFO Data Bus Bit 0 FIFO Data Bus Bit 1 FIFO Data Bus Bit 2 FIFO Data Bus Bit 3 FIFO Data Bus Bit 4 FIFO Data Bus Bit 5 FIFO Data Bus Bit 6 FIFO Data Bus Bit 7 Signal Type Description
FIFO CONTROL INTERFACE GROUP Pin# Channel A 15 Channel B 30 RXF# OUTPUT When high, do not read data from the FIFO. When low, there is data available in the FIFO which can be read by strobing RD# low then high again ** Note 1 OUTPUT When high, do not write data into the FIFO. When low, data can be written into the FIFO by strobing WR high then low. ** Note 1 INPUT Enables Current FIFO Data Byte on D0..D7 when low. Fetches the next FIFO Data Byte (if available) from the Receive FIFO Buffer when RD# goes from low to high. ** Note 1 Writes the Data Byte on the D0..D7 into the Transmit FIFO Buffer when WR goes from high to low. ** Note 1 The Send Immediate / WakeUp signal combines two functions on a single pin. If USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in the EEPROM , strobing this pin low will cause the device to request a resume on the USB Bus. Normally, this can be used to wake up the Host PC. During normal operation (PWREN# = 0), if this pin is strobed low any data in the device TX buffer will be sent out over USB on the next Bulk-IN request from the drivers regardless of the pending packet size. This can be used to optimise USB transfer speed for some applications. Tie this pin to VCCIO if not used. Signal Type Description
13 12
29 28
TXE# RD#
11 10
27 26
WR SI/WU
INPUT INPUT
**Note 1 : In Input Mode, these pins are pulled to VCCIO via internal 200K resistors. These can be programmed to gently pull low during USB suspend ( PWREN# = "1" ) by setting this option in the EEPROM. **Note 1 : During device reset, these pins are tri-state but pulled up to VCCIO via internal 200K resistors.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 3 of 51
25 FIFO Mode TIMING DIAGRAMS Figure 19 - FIFO READ Cycle
FT2232D Dual USB UART / FIFO I.C.
T6
RXF#
T5
RD#
T3
T1
T2
T4 Valid Data
Min 50 50 + T6 20 0 0 80 25 50 Max Unit ns ns ns ns ns ns
D[7...0]
Time T1 T2 T3 T4 T5 T6 Description RD# Active Pulse Width RD# to RD Pre-Charge Time RD# Active to Valid Data **Note 19
Valid Data Hold Time from RD# Inactive **Note 19 RD# Inactive to RXF# RXF# inactive after RD# cycle
** Note 19 : Load 30 pF at standard drive level. These times will also vary if the high output drive level is enabled.
Figure 20 - FIFO Write Cycle
T11
T12
TXE#
T7
T8
WR D[7...0]
Time T7 T8 T9 T10 T11 T12 Description WR Active Pulse Width WR to WR Pre-Charge Time Data Setup Time before WR inactive Data Hold Time from WR inactive WR Inactive to TXE# TXE inactive after WR cycle Min 50 50 20 0 5 80
T9 Valid Data
Max Unit ns ns ns ns 25 ns ns
T10
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 35 of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 21 - Microprocessor Interface Example
FT2232C
Channel A or B
D0 D1 D2 D3 D4 D5 D6
FT2232D
Microcontroller
IO10 IO11
IO13 IO14 IO15 IO16 IO17 IO20 IO21 IO22 IO23 IO24 IO25
D7 RD# WR TXE# RXF# SI / WU PWREN#
41
( Optional ) ( Optional )
Figure 21 illustrates a typical interface between one of the channels of the FT2232D, configured in 245-style FIFO interface mode, and a MicroController (MCU). Either channel A or B, or both can be configured in this mode. This examples uses two IO Ports of the MCU, one port (8 bits) to transfer data to one of the and the other port (4 / 5 bits) to monitor the TXE# and RXF# status bits and generate the RD# and WR strobes to the FT2232D as required. Optionally, SI / WU can be connected to another IO pin if either of the functions of this pin are required. If the SI / WU function is not required, tie this pin to VCCIO. If the MCU is handling power management functions, then PWREN# should also be connected to an IO pin of the MCU. The 8 data bits on IO Port 1 can be shared with other peripherals when the MCU is not accessing the FT2232D.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 36 of 51
IO Port 2
IO Port 1
IO12
FT2232D Dual USB UART / FIFO I.C.
9.5 Enhanced Asynchronous and Synchronous Bit-Bang Modes - Signal Description and Interface Configuration
Bit-bang mode is a special FT2232D device mode that changes the 8 IO lines on either (or both) channels into an 8 bit bi-directional data bus. The are two types of bit bang mode for the FT2232D - Enhanced Asynchronous Bit-Bang Mode, which is virtually the same as FTDI BM chip-style Bit-Bang mode, with the addition of Read and Write strobes; and Synchronous Bit-Bang mode, where data is only read from the device when the device is written to. Bit-Bang mode is enabled by driver command. When either Channel A or Channel B (or both) have Enhanced Asynchronous Bit-Bang mode, or Synchronous Bit-Bang mode enabled the IO signal lines are configured as follows :BIT-BANG DATA BUS GROUP **Note 2 Pin# Channel A 24 23 22 21 20 19 17 16 Channel B 40 39 38 37 36 35 33 32 D0 D1 D2 D3 D4 D5 D6 D7 I or O I or O I or O I or O I or O I or O I or O I or O Bit-Bang Data Bus Bit 0 Bit-Bang Data Bus Bit 1 Bit-Bang Data Bus Bit 2 Bit-Bang Data Bus Bit 3 Bit-Bang Data Bus Bit 4 Bit-Bang Data Bus Bit 5 Bit-Bang Data Bus Bit 6 Bit-Bang Data Bus Bit 7 Signal Type Description
BIT-BANG CONTROL INTERFACE GROUP Pin# Channel A 15 13 12 11 10 Channel B 30 29 28 27 26 WR# RD# WR# RD# SI/WU OUTPUT **Note 25 OUTPUT **Note 25 OUTPUT **Note 26 OUTPUT **Note 26 INPUT The Send Immediate / WakeUp signal combines two functions on a single pin. If USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in the EEPROM , strobing this pin low will cause the device to request a resume on the USB Bus. Normally, this can be used to wake up the Host PC. During normal operation (PWREN# = 0), if this pin is strobed low any data in the device TX buffer will be sent out over USB on the next Bulk-IN request from the drivers regardless of the pending packet size. This can be used to optimise USB transfer speed for some applications. Tie this pin to VCCIO if not used. Signal Type Description
**Note 2 : In Input Mode, these pins are pulled to VCCIO via internal 200K resistors. These can be programmed to gently pull low during USB suspend ( PWREN# = "1" ) by setting this option in the EEPROM.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 3 of 51
FT2232D Dual USB UART / FIFO I.C.
**Note 25 : The Bit-Bang Mode (synchronous and asynchronous) WR# and RD# strobes are on these pins when the main Channel mode is 245 FIFO, or Fast Opto-Isolated Serial Mode. Bit-Bang mode is not available on Channel B when Fast Opto-Isolated Serial Mode is enabled. **Note 26 : The Bit-Bang Mode (synchronous and asynchronous) WR# and RD# strobes are on these pins when the main Channel mode is set to 232 UART Mode.
Enhanced Asynchronous Bit-Bang Mode
Enhanced Asynchronous Bit-Bang mode is the same as BM-style Bit-Bang mode, except that the internal RD# and WR# strobes are now brought out of the device to allow external logic to be clocked by accesses to the bit-bang IO bus. On either or both channels any data written to the device in the normal manner will be self clocked onto the data pins (those which have been configured as outputs). Each pin can be independently set as an input or an output. The rate that the data is clocked out at is controlled by the baud rate generator. For the data to change there has to be new data written, and the baud rate clock has to tick. If no new data is written to the channel, the pins will hold the last value written. To allow time for the data to be setup and held around the WR# strobe, the baud rate should be less than 1 MegaBaud. See the application note AN232B-01, "FT232BM/FT245BM Bit Bang Mode" for more details and a sample application. Enabling Asynchronous Bit-Bang mode is enabled using Set Bit Bang Mode driver command. A hex value of 1 will enable it, and a hex value of 0 will reset the device. See application note AN2232L-02, "Bit Mode Functions for the FT2232D" for more details and examples of this.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 3 of 51
FT2232D Dual USB UART / FIFO I.C.
Synchronous Bit-Bang Mode
With Synchronous Bit-Bang mode data will only be sent out by the FT2232D if there is space in the device for data to be read from the pins. This Synchronous Bit-Bang mode will read the data bus pins first, before it sends out the byte that has just been transmitted. It is therefore 1 byte behind the output, and so to read the inputs for the byte that you have just sent, another byte must be sent. For example :(1) Pins start at 0xFF Send 0x55,0xAA Pins go to 0x55 and then to 0xAA Data read = 0xFF,0x55 (2) Pins start at 0xFF Send 0x55,0xAA,0xAA (repeat the last byte sent) Pins go to 0x55 and then to 0xAA Data read = 0xFF,0x55,0xAA
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 39 of 51
FT2232D Dual USB UART / FIFO I.C.
Enabling Synchronous Bit-Bang mode is enabled using Set Bit Bang Mode driver command. A hex value of 4 will enable it, and a hex value of 0 will reset the device. See application note AN2232L-02, "Bit Mode Functions for the FT2232D" for more details and examples.
Figure 25 - Synchronous Bit Bang Mode Signal Timing
t1 Clk Time D7..0 WR# RD#
Current Data
t2
t3
t4
t5
t6
New Data
Time t1 t2 t3 t4 t5 t6
Description Current pin state is read RD# is set inactive RD# is set active again, and any pins that are output will change to the new data. Clock state for data setup WR# goes active WR# goes inactive
The internal RD# and WR# strobes are brought out of the device to allow external logic to be clocked by accesses to the bit-bang IO bus.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 0 of 51
FT2232D Dual USB UART / FIFO I.C.
9.6 Multi-Protocol Synchronous Serial Engine (MPSSE) Mode Signal Descriptions and Interface Configurations
MPSSE Mode is designed to allow the FT2232D to interface efficiently with synchronous serial protocols such as JTAG and SPI Bus. It can also be used to program SRAM based FPGA's over USB. The MPSSE interface is designed to be flexible so that it can be configured to allow any synchronous serial protocol (industry standard or proprietary) to be interfaced to the FT2232D. MPSSE is available on channel A only. MPSSE is fully configurable, and is programmed by sending commands down the data pipe. These can be sent individually, or more efficiently in packets. MPSSE is capable of a maximum sustained data rate of 5.6 Mega bits / s. When Channel A is configured in MPSSE mode the IO signal lines are configured as follows :Pin# Signal (Channel A Only) 24 23 22 21 20 19 17 16 15 13 12 11 TCK/SK TDI/D0 TDO/DI GPIOL0 GPIOL1 GPIOL2 GPIOL3 Type OUTPUT OUTPUT INPUT I/O I/O I/O I/O Description Clock signal Output Serial Data Out Serial Data In **Note 2 Select Signal Out General Pupose input / Output **Note 2 General Pupose input / Output **Note 2 General Pupose input / Output **Note 2 General Pupose input / Output **Note 2 General Pupose input / Output **Note 2 General Pupose input / Output **Note 2 General Pupose input / Output **Note 2 General Pupose input / Output **Note 2
TMS/CS OUTPUT
GPIOH0 I/O GPIOH1 I/O GPIOH2 I/O GPIOH3 I/O
**Note 2 : In Input Mode, these pins are pulled to VCCIO via internal 200K resistors. These can be programmed to gently pull low during USB suspend ( PWREN# = "1" ) by setting this option in the EEPROM. Enabling MPSSE mode is enabled using Set Bit Bang Mode driver command. A hex value of 2 will enable it, and a hex value of 0 will reset the device. See application note AN2232L-02, "Bit Mode Functions for the FT2232D" for more details and examples. The MPSSE command set is fully described in application note AN2232L-01 - "Command Processor For MPSSE and MCU Host Bus Emulation Modes".
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 1 of 51
FT2232D Dual USB UART / FIFO I.C.
9.7
MCU Host Bus Emulation Mode Signal Descriptions and Interface Configuration
MCU host bus emulation mode uses both of the FT2232D's A and B channel interfaces to make the chip emulate a standard 8048 / 8051 MCU host bus. This allows peripheral devices for these MCU families to be directly connected to USB via the FT2232D. The lower 8 bits (AD7 to AD0) is a multiplexed Address / Data bus. A8 to A15 provide upper (extended) addresses. There are 4 basic operations :1) Read (does not change A15 to A8) 2) Read Extended (changes A15 to A8) 3) Write (does not change A15 to A8) 4) Write Extended (changes A15 to A8)
Enabling MCU Host Bus Emulation mode is enabled using Set Bit Bang Mode driver command. A hex value of 8 will enable it, and a hex value of 0 will reset the device. See application note AN2232L-02, "Bit Mode Functions for the FT2232D" for more details and examples. The MCU Host Bus Emulation Mode command set is fully described in application note AN2232L-01 - "Command Processor For MPSSE and MCU Host Bus Emulation Modes".
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 2 of 51
FT2232D Dual USB UART / FIFO I.C.
When MCU Host Bus Emulation mode is enabled the IO signal lines on both channels work together and the pins are configured as follows :Pin# 24 23 22 21 20 19 17 16 15 13 Signal AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 I/O0 I/O1 Type I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Description Address / Data Bus Bit 0 **Note 2 Address / Data Bus Bit 1 **Note 2 Address / Data Bus Bit 2 **Note 2 Address / Data Bus Bit 3 **Note 2 Address / Data Bus Bit 4 **Note 2 Address / Data Bus Bit 5 **Note 2 Address / Data Bus Bit 6 **Note 2 Address / Data Bus Bit 7 **Note 2 MPSSE mode instructions to set / clear or read the high byte of data can be used with this pin. **Note 28, **Note 29 MPSSE mode instructions to set / clear or read the high byte of data can be used with this pin. In addition this pin has instructions which will make the controller wait until it is high, or wait until it is low. This can be used to connect to an IRQ pin of a peripheral chip. The FT2232D will wait for the interrupt, and then read the device, and pass the answer back to the host PC. I/O1 must be held in input mode if this option is used. **Note 28, **Note 29 Extends the time taken to perform a Read or Write operation if pulled low. Pull up to Vcc if not being used. Shows the clock signal that the circuit is using. Extended Address Bus Bit 8 Extended Address Bus Bit 9 Extended Address Bus Bit 10 Extended Address Bus Bit 12 Extended Address Bus Bit 13 Extended Address Bus Bit 14 Extended Address Bus Bit 15 Extended Address Bus Bit 16 Negative pulse to select device during Read or Write. Positive pulse to latch the address. Negative Read Output. Negative Write Output. (Data is setup before WR# goes low, and is held after WR# goes high)
12 11 40 39 38 37 36 35 33 32 30 29 28 27
IORDY OSC A8 A9 A10 A11 A12 A13 A14 A15 CS# ALE RD# WR#
INPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
**Note 2 : In Input Mode, these pins are pulled to VCCIO via internal 200K resistors. These can be programmed to gently pull low during USB suspend ( PWREN# = "1" ) by setting this option in the EEPROM. **Note 29 : These instrucions are fully described in the application note AN2232L-01 - "Command Processor For MPSSE and MCU Host Bus Emulation Modes".
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 3 of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 29 - MCU Host Bus Emulation Mode Signal Timing - Write Cycle
t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11
OSC A15..A8 AD7..0 ALE CS# WR# IORDY
High Address Low Address Data
Time t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11
Description High address byte is placed on the bus if the extended write is used. Low address byte is put out. 1 clock period for address is set up. ALE goes high to enable latch. This will extend to 2 clocks wide if IORDY is low. ALE goes low to latch address and CS# is set active low. Data driven onto the bus. 1 clock period for data setup. WR# is driven active low. This will extend to 6 clocks wide if IORDY is low. WR# is driven inactive high. CS# is driven inactive, 1/2 a clock period after WR# goes inactive Data is held until this point, and may now change
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 30 - MCU Host Bus Emulation Mode Signal Timing - Read Cycle
t1 t2 t3 t4 t5 t6 t7 t8 t9
OSC A15..A8 AD7..0 ALE CS# RD# IORDY
Time t1 t2 t3 t4 t5 t6 t7 t8 t9 Description High address byte is placed on the bus if the extended read is used - otherwise t1 will not occur. Low address byte is put out. 1 clock period for address set up. ALE goes high to enable address latch. This will extend to 2 clocks wide if IORDY is low. ALE goes low to latch address, and CS# is set active low. This will extend to 3 clocks if IORDY is sampled low. CS# will always drop 1 clock after ALE has gone high no matter the state of IORDY. Data is set as input (Hi-Z), and RD# is driven active low. 1 clock period for data setup. This will extend to 5 clocks wide if IORDY# is sampled low. RD# is driven inactive high. CS# is driven inactive 1/2 a clock period after RD# goes inactive, and the data bus is set back to output.
High Address Low Address Hi-Z
Figure 31 - MCU Host Bus Emulation Mode Signal Timing - Clock (OSC) Signal
thigh
OSC
tlow
Time Description Clock Period Clock signal high time Clock signal low time
tperiod
Typical Value 83.3 41.6 41.6 Maximum 125.0 62.5 62.5 Unit ns ns ns
Minimum 41.6 20.8 20.8
tperiod thigh tlow
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 5 of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 32 - MCU Host Bus Emulation Example - USB <=> CAN Bus Interface
FT2232C FT2232D
CS# (BCBUS0) ALE (BCBUS1) RD# (BCBUS2) WR# (BCBUS3) 30 29 28 27 CS# ALE/AS RD# WR#
SJA1000 CANBus Controller
Tx
CANBus Transeiver
Rx
AD[0...7] (ADBUS[0...7])
ADDRESS / DATA BUS
AD[0...7]
CAN Bus
Vcc
Vcc
IORDY# (ACBUS2) I/O0 (ACBUS0) I/O1 (ACBUS1)
12 15 13
MODE
INT#
Figure 32 shows an example where the FT2232D is used to interface a Philips SJA1000 CAN Bus Controller to a PC over USB. In this example IORDY is not used and so is pulled up to Vcc. I/O1 is used to monitor the Interrupt output (INT) of the SJA1000. The MODE pin on the SJA1000 is pulled high to select Intel mode. See the semiconductors section of the Philips website (www.philips.com) for more details on the SJA1000, and suitable CAN Bus transceiver devices.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 6 of 51
FT2232D Dual USB UART / FIFO I.C.
9.8
Fast Opto-Isolated Serial Interface Mode Signal Description and Configuration
Fast Opto-Isolated Serial Interface Mode provides a method of communicating with an external device over USB using 4 wires that can have opto-isolators in their path, thus providing galvanic isolation between systems. If either channel A or channel B are enabled in fast opto-isolated serial mode then the pins on channel B are switched to the fast serial interface configuration. The I/O interface for fast serial mode is always on channel B, even if both channels are being used in this mode. An address bit is used to determine the source or destination channel of the data. It therefore makes sense to always use at least channel B or both for fast serial mode, but not A own its own. When either Channel B or Both Channel A and B are configured in Fast Opto-Isolated Serial Interface mode following IO signal lines are configured as follows :Pin# 40 39 Signal FSDI FSCLK Type INPUT INPUT Description Fast serial data input **Note 30 Clock input to FT2232D chip to clock data in or out. The external device has to provide a clock signal or nothing will change on the interface pins. This gives the external device full control over the interface. It is designed to be half duplex so that data is only transferred in one direction at a time. **Note 30 Fast serial data output. Driven low to indicate that the chip is ready to send data. Clear To Send control signal output The Send Immediate / WakeUp signal combines two functions on a single pin. If USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in the EEPROM , strobing this pin low will cause the device to request a resume on the USB Bus. Normally, this can be used to wake up the Host PC. During normal operation (PWREN# = 0), if this pin is strobed low any data in the device TX buffer will be sent out over USB on the next Bulk-IN request from the drivers regardless of the pending packet size. This can be used to optimise USB transfer speed for some applications. Tie this pin to VCCIO if not used.
38 37 26
FSDO FSCTS SI/WU
OUTPUT OUTPUT INPUT
**Note 30 : Pulled up to VCCIO via internal 200K resistors. These pins can be programmed to gently pull low during USB suspend ( PWREN# = "1" ) by setting this option in the EEPROM. Fast Opto-Isolated serial interface mode is enabled in the external EEPROM.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 33 - Fast Opto-Isolated Serial Signal Timing Diagram FSCLK
t1
FSDO / FSCTS
t2
t5 t7
t6
FSDI
t3
t4
Time t1 t2 t3 t4 t5 t6 t7
Description FSDO / FSCTS hold time FSDO / FSCTS setup time FSDI hold time FSDI setup time FSCLK low FSCLK high FSCLK Period
Min 5 5 5 10 10 10 20
Max -
Unit ns ns ns ns ns ns ns
-
Outgoing Fast Serial Data
To send fast serial data out of the chip, the external device must clock. If the chip has data ready to send, it will drive FSDO low to indicate the start bit. It will not do this if it is currently receiving data from the external device.
Figure 3 - Fast Opto-Isolated Serial Data Format - Data output from the FT2232D FSCLK FSDO
0 Start Bit D0 D1 D2 D3 D4 D5 D6 D7 SRCE Source Bit
Data Bits - LSB first
Notes :(i) Start Bit is always 0. (ii) Data is sent LSB first. (iii) The source bit (SRCE) indicates which channel the data has come from. A `0' means that it has come from Channel A, a `1' means that it has come from Channel B. (iv) If the target device is unable to accept the data when it detects the start bit, it should stop the FSCLK until it can accept the data. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page of 51
FT2232D Dual USB UART / FIFO I.C.
Incoming Fast Serial Data
The external device is allowed to send data into the chip if FSCTS is high. On receipt of a Zero start bit on FSDI, the chip will drop FSCTS on the next positive clock edge. The data from bits 0 to 7 is then clocked in (LSB first). The next bit determines where the data will be written to. It can go to either channel A or to channel B. A `0' will send it to channel A, providing channel A is enabled for fast serial mode, otherwise it will go to channel B. A `1' will send it to channel B, providing channel B is enabled for fast serial mode, otherwise it will go to channel A. ( Either channel A, or channel B, or both must be enabled as fast serial mode or the circuit is disabled).
Figure 35 - Fast Opto-Isolated Serial Data Format - Data input to the FT2232D FSCTS FSCLK FSDI
0 Start Bit D0 D1 D2 D3 D4 D5 D6 D7 DEST Destination Bit
Data Bits - LSB first
Notes :(i) Start Bit is always 0. (ii) Data is sent LSB first. (iii) The destination bit (DEST) indicates which channel the data should go to. A `0' means that it should go to channel A, a `1' means that it should go to channel B. (iv) The target device should check CTS is high before it sends data. CTS goes low after data bit 0 (D0) and stays low until the chip can accept more data.
Contention
There is a possibility that contention may occur, where the interface goes from being completely idle to both sending and receiving at the same clock instance. In this case the chip backs off, and allows the data from the external device to be received.
Data Format
The data format for either direction is :1) Zero Start Bit 2) Data bit 0 3) Data bit 1 4) Data bit 2 5) Data bit 3 6) Data bit 4 7) Data bit 5 8) Data bit 6 9) Data bit 7 10) Source/Destination (`0' indicates channel A; `1' indicates channel B)
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 9 of 51
FT2232D Dual USB UART / FIFO I.C.
Reset / Enable
Fast serial mode is enabled by setting the appropriate bits in the external EEPROM. The fast serial mode can be held in reset by setting a bit value of 10 using the Set Bit Bang Mode command. While this bit is set the device is held reset - data can be sent to the device, but it will not be sent out by the device until the device is enabled again. This is done by sending a bit value of 0 using the set bit mode command. See application note AN2232L-02, "Bit Mode Functions for the FT2232D" for more details and examples.
Figure 36 - Fast Opto-Isolated Serial Interface Example
VCC5V
Cable
8
FT2232D FT2232C
FSDI (BDBUS0) FSCLK (BDBUS1) 40 1K
HCPL-2430
VCCE
1 470R
1K 7 6 5 2 3
DI CLK
39
470R 4
VCC5V 1 38 37 470R 4 470R 2 3
VCCE
HCPL-2430
8 1K 7 6 5 1K DO CTS
FSDO (BDBUS2) FSCTS (BDBUS0)
In the example shown in figure 12 two Agilent HCPL-2430 (see the semiconductor section at www.agilent.com) high speed opto-couplers are used to optically isolate an external device which interfaced to USB using the FT2232D. In this example VCC5V is the supply for the FT2232D (bus or self powered), and VCCE is the supply to the external device. Care must be taken with the voltage used to power the photoLED's. It should be the same supply that the I/Os are driving to, or the LED's may be permanently on. Limiting resistors should be fitted in the lines that drive the diodes. The outputs of the opto-couplers are open-collector and so need a pullup resistor.
Testing
Fast serial mode has been tested using an Scenix (Ubicom), SX28 microcontroller (see www.ubicom.com) which was configured in loopback mode. This was done both with, and without HP HCPL-2430 opto-isolators in place. The isolators add a considerable delay to the turnaround time seen by the micro. This was close to 100 nS with the high speed HCPL-2430 device. This is the combined delay of the clock signal from the microcontroller going through an opto-coupler to the chip, and the data from the FT2232D chip going through the other opto-coupler back to the microcontroller. DS2232D Version 0.91 (c) Future Technology Devices International Ltd. 2006 Page 50 of 51
FT2232D Dual USB UART / FIFO I.C.
9.9
CPU FIFO Interface Mode Signal Descriptions and Configuration Examples
CPU-style FIFO interface mode is designed to allow a CPU to interface to USB via the FT2232D. This mode is enabled in the external EEPROM. The interface is achieved using a chip select bit (CS#) and address bit (A0). When either Channel A or Channel B are in CPU FIFO Interface mode the IO signal lines are configured as follows:FIFO DATA BUS GROUP **Note 20 Pin# Channel A 24 23 22 21 20 19 17 16 Channel B 40 39 38 37 36 35 33 32 D0 D1 D2 D3 D4 D5 D6 D7 I/O I/O I/O I/O I/O I/O I/O I/O FIFO Data Bus Bit 0 FIFO Data Bus Bit 1 FIFO Data Bus Bit 2 FIFO Data Bus Bit 3 FIFO Data Bus Bit 4 FIFO Data Bus Bit 5 FIFO Data Bus Bit 6 FIFO Data Bus Bit 7 Signal Type Description
FIFO CONTROL INTERFACE GROUP Pin# Channel A 15 13 12 11 Channel B 30 29 28 27 CS# A0 RD# WR# INPUT INPUT INPUT INPUT Chip Select Bit ** Note 20 Address Bit ** Note 20 Negative read input ** Note 20 Negative write input ** Note 20 Signal Type Description
**Note 20 : In Input Mode, these pins are pulled to VCCIO via internal 200K resistors. These can be programmed to gently pull low during USB suspend ( PWREN# = "1" ) by setting this option in the EEPROM. Chip Select bit and Address bit truth table CS# 1 0 0 A0 X 0 1 RD# X Read Data Pipe Read Status WR# X Write Data Pipe Send Immediate **Note 21
Key : X = Not Used; 1 = Signal off; 0 = Signal off **Note 21 : Has to be clocked by USB clock.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 51 of 51
FT2232D Dual USB UART / FIFO I.C.
Status Data bits Data Bit bit 0 bit 1 bit 2 bit 3 bit 4 **Note 22 bit 5 **Note 22 bit 6 **Note 22 bit 7 **Note 22 Data 1 1 1 1 X X X X Status Data Available (=RXF) Space Available (=TXE) Suspend Configured X X X X
Key : X = Not Used; 1 = Signal off; 0 = Signal off **Note 22 : bits 4 to 7 will have arbitrary values when the status is read.
Figure 3 - CPU FIFO Interface Mode - Signal Timing
A0 CS# WR# RD# D7..0
t2
Time t1 t2 t3 t4 t5 t6 t7 t8 t9 Description A0 / CS Setup to WR# Data setup to WR# WR# Pulse width A0/CS Hold from WR# Data hold from WR# A0/CS Setup to RD# Data delay from RD# **Note 23 A0/CS hold from RD# Data hold time from RD# **Note 23
Valid t3 t1 t4 t6 Valid t5
Min 15 15 20 5 5 15 15 5 0
Valid
Valid t7
Max 50 30 Unit ns ns ns ns ns ns ns ns ns
**Note 23 : For standard output drive level Times may vary if high drive level is enabled.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 52 of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 3 - CPU FIFO Single Channel Interface Example 1
Decoder
FT2232D FT2232C
CPU
Address Bus 15 13 A0 (ACBUS1) 12 RD# 11 WR# WR# (ACBUS3) RD# (ACBUS2)
Channel A
CS# (ACBUS0)
Data Bus
Data
D[0...7] (ADBUS[0...7])
Figure 23 shows an example where channel A of the FT2232D is used in CPU FIFO mode to interface with a CPU. To read or write data to or from the CPU to the FT2232D, the FT2232D's Chip Select (CS#) would be set to 0. In order to read the status of the device the Address bit would then be set to 1, and RD# would be strobed causing the status data to be driven onto D0...D7. If data is available (D0 = 1) then it can be read by setting A0 to 0, and strobing RD#. If space is available (D1=1) then data can be written to the FT2232D by setting A0 to 0 and strobing WR#. When CS# is set to 0 and A0 is set to 1, strobing WR# causes any data in the FT2232D's TX buffer to be sent out over USB on the next Bulk-In request, regardless of the pending packet size.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 53 of 51
FT2232D Dual USB UART / FIFO I.C.
Figure 39 - CPU FIFO Dual Channel Interface Example 2
Decoder
FT2232C FT2232D CPU
Address Bus 15 13 12 11
Channel A
CS#_A (ACBUS0) A0_A (ACBUS1) RD#_A (ACBUS2) WR#_A (ACBUS3)
RD# WR#
Data Bus
Data
D[0...7]A (ADBUS[0...7])
Channel B
30 29 28 27
CS#_B (BCBUS0) A0_B (BCBUS1) RD#_B (BCBUS2) WR#B (BCBUS3)
D[0...7]B (BDBUS[0...7])
Figure 24 shows an example where both channels A and B of the FT2232D are used in CPU FIFO mode to interface with a CPU. This configuration gives the CPU access to both of the FT2232D's data pipes.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 5 of 51
FT2232D Dual USB UART / FIFO I.C.
10.0 Document Revision History
DS2232L Version 0.9 - Initial document created October 2006.
11.0 Disclaimer
(c) Future Technology Devices International Limited , 2006 Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd. will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 55 of 51
FT2232D Dual USB UART / FIFO I.C.
12.0 Contact Information
Head Office Future Technology Devices International Ltd. 373 Scotland Street, Glasgow G5 8QB, United Kingdom Tel. : +(44) 141 429 2777 Fax. : +(44) 141 429 2758 E-Mail (Sales) : sales1@ftdichip.com E-Mail (Support) : support1@ftdichip.com E-Mail (General Enquiries) : admin1@ftdichip.com Regional Sales Offices Future Technology Devices International Ltd. (Taiwan) 4F, No 16-1, Sec. 6 Mincyuan East Road, Neihu District, Taipei 114, Taiwan, R.o.C. Tel.: +886 2 8791 3570 Fax: +886 2 8791 3576 E-Mail (Sales): tw.sales@ftdichip.com E-Mail (Support): tw.support@ftdichip.com E-Mail (General Enquiries): tw.admin@ftdichip.com Future Technology Devices International Ltd. (USA) 5285 NE Elam Young Parkway, Suite B800 Hillsboro, OR 97124-6499 USA Tel.: +1 (503) 547-0988 Fax: +1 (503) 547-0987 E-Mail (Sales): us.sales@ftdichip.com E-Mail (Support): us.support@ftdichip.com E-Mail (General Enquiries): us.admin@ftdichip.com
Website URL : http://www.ftdichip.com Agents and Sales Representatives At the time of writing our Sales Network covers over 40 different countries world-wide. Please visit the Sales Network page of our Web site for the contact details our distributor(s) in your country.
DS2232D Version 0.91
(c) Future Technology Devices International Ltd. 2006 Page 56 of 51

▲Up To Search▲

Price & Availability of FT2232D

	To Download FT2232D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .